Reticon LC3000 Series Manuale delle Istruzioni

www .perkinelmer .com/opto LC3000-Series Camera Instruction ManualINSTRUCTION MANUALImagingDigital ImagingPerkinElmer Optoelectronics2175 Mission Coll

PerkinElmer Optoelectronics 64.1.1 Master ModeThe master mode is a stand-alone operating mode that requires only DC powerfor operation. Master mode

7 PerkinElmer Optoelectronics4.1.2.1 Exposure ControlSlave mode camera exposure is determined by the LR and LT signals which mustbe timed with MCLK.

PerkinElmer Optoelectronics 84.1.3 Alt Slave Mode 1Alt Slave Mode 1 operates similarly to the Slave Mode except that the cameraoperates on the inter

9 PerkinElmer Optoelectronics5 Installation GuidelinesThe following guidelines are offered as an aid to permit the user for setting up thecamera suc

PerkinElmer Optoelectronics 105.1.1 Estimating the Working DistanceThe following relationships assume a thin lens relationship that is deemedsuffici

11 PerkinElmer Optoelectronics5.2 Lens AttachmentThe LC3000 series cameras provide threaded mounting holes on the front face ofthe cameras to allow

PerkinElmer Optoelectronics 12Figure 7 LC3000 Series Camera Mounting Hole LocationNote: For best thermal stability, mount the camera to a flat metal

13 PerkinElmer Optoelectronics5.5 Interface CablingThe signal interface cable supports an RS-422 interface to receive the externalLT, LR and MCLK si

PerkinElmer Optoelectronics 145.6 Frame Grabber Interface GuidelinesThe LC3000 series cameras have been designed for use with several brands offram

15 PerkinElmer Optoelectronics6 Camera SetupThis section provides a generalized procedure for installing, configuring and activatingyour camera. Sin

PerkinElmer Optoelectronics iiCopyrights, Patents and Trademark CreditsPerkinElmer, the PerkinElmer Logo and the stylized P are trademarks of PerkinE

PerkinElmer Optoelectronics 167. Power up the system computer and verify that the frame grabber isoperational.6.2.1 Tripod MountingThe LC3000 serie

17 PerkinElmer Optoelectronics6.3 Activating the CameraPlace the test target within the cameras’ projected field of view and turn on theillumination

PerkinElmer Optoelectronics 186.4 Camera ControlCamera control includes camera operating mode, video offset and video gain.Each of these parameters

19 PerkinElmer Optoelectronics6.4.3 Video OffsetVideo Offset is determined by DIP switches 6, 7 and 8 as shown in Table 6Table 6 Video Offset Sel

PerkinElmer Optoelectronics 206.5 Verifying Slave Mode OperationNote: In order to verify the Slave Mode you must have made provisions for the requir

21 PerkinElmer Optoelectronics7 Target Speed Determination7.1 Target Speed and Exposure RelationshipsThe following definitions apply:Image Resoluti

PerkinElmer Optoelectronics 227.2 Sample Imaging SetupThe following example assumes that you have determined the following:· Target width X· Image

23 PerkinElmer Optoelectronics8 Troubleshooting8.1 Troubleshooting Check ListNo Video1. Verify that the power to the camera is on.2. Verify that

PerkinElmer Optoelectronics 248.3 Contacting Customer SupportUnited States PerkinElmer Optoelectronics2175 Mission College Blvd.Santa Clara, CA 9505

25 PerkinElmer OptoelectronicsAPPENDIX A Interface GuidelinesA.1 RS-422 Digital InterfaceThe LC3000 series digital signals are received and trans

iii PerkinElmer OptoelectronicsTable of Contents1 INTRODUCTION ...

PerkinElmer Optoelectronics 26A.2 Video ReceiverFigure 12 Recommended Video Line Receiver Circuit

27 PerkinElmer OptoelectronicsIndexAAlt Slave Mode 1, 8Alt Slave Mode 2, 8CCameraactivating, 17installing, 15mounting, 11Operation overview, 5Camera

PerkinElmer Optoelectronics iv6.5 VERIFYING SLAVE MODE OPERATION...207 TARGET SPEED DETE

1 PerkinElmer Optoelectronics1 Introduction1.1 What’s In this ManualThis manual describes the receiving, unpacking and inspection of your LC3000ser

PerkinElmer Optoelectronics 2Figure 1 LC3000 Series Camera Block Diagram

3 PerkinElmer Optoelectronics2 Typical InstallationFigure 2 illustrates a typical machine vision installation showing the majorsystem components and

PerkinElmer Optoelectronics 43 Receiving and Inspecting Your Camera3.1 Unpacking Your CameraInspect the received shipping container for any damage

5 PerkinElmer Optoelectronics4 Camera Operation OverviewThe camera operation is a 2 stage process that consists of exposure and dataoutput transfer